1. 
         
         
         
         

    2. <optgroup id="1d1a6125"></optgroup>

        热竞技竞猜手机版

        News

        商家动态

        您的岗位:主页 > 热竞技竞猜手机版 > 商家动态 >

        热竞技竞猜客户端在一般中的常见问题及解决方案

        通告时间:2018-07-23     来源:艾德威尔•瑞拓
        热竞技竞猜客户端在利用过程必然会出现一些问题,少数是出于操作人员的不规范造成的,局部是热竞技竞猜客户端的普通磨损所造成的,那些题材的出现都会影响我热竞技竞猜客户端的例行使用,下我们了解一下热竞技竞猜客户端的常见问题及解决方案。
        There will inevitably be some problems in the use of high temperature butterfly valves, some of which are caused by the improper operation personnel, and some are caused by the daily wear of high temperature butterfly valves. The occurrence of these problems will affect the normal use of my high temperature butterfly valves.

        一、题目分析:
        I. problem analysis:

        热竞技竞猜客户端执行机构完全关闭的状态下,阀板密封间隙上下应均匀分布。但热竞技竞猜客户端采用水平安装调试使用,阀体因难度差所引起的变形主要来自于蝶阀受自身重力和阀板阀轴、传动装置和附件重力作用产生变形,蝶阀水平安装阀体变形后与管路相联接,她变形得不到恢复保持下去。阀体变形后,阀体通道呈长方形,导致阀体密封圈与阀板密封圈不能均匀的接触。
        When the high temperature butterfly valve actuator is completely closed, the upper and lower sealing clearance of the valve plate should be evenly distributed. However, the high temperature butterfly valve adopts horizontal installation and adjustment. The deformation of the valve body due to the difference in rigidity mainly comes from the deformation of the butterfly valve caused by its own gravity and the action of the valve plate valve shaft, transmission device and attachment gravity. After the valve body is deformed, the valve body channel is oval, causing the valve body seal ring and the valve plate seal ring cannot even contact.

        ②热竞技竞猜客户端靠蝶板控制管路内部的腐殖质,在截断时,蝶板受高温介质的压力作用而产生变形,使蝶板的全封闭面与阀体密封面脱离,决不能有效的起到密封效果。严重时,使阀板的旋转受到卡阻,阀门不能正常工作。
        In case of truncation, the butterfly valve with high temperature controls the medium inside the pipeline by the butterfly plate. As a result, the butterfly plate is deformed by the pressure of the high temperature medium, so that the sealing surface of the butterfly plate is separated from the sealing surface of the valve body, and the sealing effect cannot be effectively achieved. In severe cases, the valve plate rotation is blocked and the valve cannot work normally.

        ③介质高温烟气中含有大量催化剂粉尘、水蒸气,户均会产生积聚。热竞技竞猜客户端在遥远不动作时也可能造成阀门阻塞卡位。
        As a result, a large amount of catalyst dust and water vapor can be accumulated in high temperature flue gas. The high temperature butterfly valve may also cause the valve to block the position when not operating for a long time.

        ④热竞技竞猜客户端因仪表伺服阀经常出现供压不够,导致阀位调节系统无法控制阀板开关到位,有效阀体机械行程与信号的表现不一致。
        High temperature butterfly valves often have insufficient pressure supply due to meter servo valves, so the valve position control system cannot control the valve plate switch in place, making the mechanical stroke of valve body inconsistent with the signal display.

        热竞技竞猜客户端
        High temperature butterfly valve


        热竞技竞猜客户端


        二、解决方案:
        Ii. Solutions:

        热竞技竞猜客户端仪表伺服阀供电不足的题目在跟换配件后就能健康使用。重在问题是检修拆卸阀体后,察觉液压执行机构在路最大时,热竞技竞猜客户端阀板与密封面之间的还有60mm间隙。穿越对阀体执行机构的分裂分析,液压缸的最大行程有限定且不能进行更改,据此不能通过行程来调节阀板的最大运转角度以达到密封。途经研究,规划出了最新结构键来解决上述存在的较大间隙问题,并且经过强度校核计算,最新结构键能够满足机械强度设计要求和工艺要求。阀轴的重中之重意图就是在工艺需求和仪表信号的支配下按照一定的能见度进行旋转,穿越键的图把扭矩传递给阀板以达到阀开度的要求。保持阀板对阀体的相对位置,阀轴要承担介质的水力和传递驱动装置对蝶板的传动力,合同阀门的调整控制或截断功能。要改变键的构造来补充阀板密封不到位的症结,必须先通确定键所需的补充位置(补宽度)。

        The problem of insufficient power supply of servo valve of high temperature butterfly valve instrument can be used normally after following the replacement of parts. The main problem is that after overhaul and disassembly of valve body, it is found that there is a 60mm gap between high temperature butterfly valve plate and sealing cover when the hydraulic actuator has the maximum stroke. Through the disintegration analysis of the valve body actuator, the maximum stroke of the hydraulic cylinder is limited and cannot be changed, so the maximum running Angle of the valve plate cannot be adjusted through the stroke to achieve sealing. After research, a new type of structural key is designed to solve the above problems of large gap. After strength check calculation, the new type of structural key can meet the mechanical strength design requirements and technological requirements. The main function of the valve shaft is to rotate at a certain Angle under the control of process requirements and instrument signals, and transfer torque to the valve plate through the action of the key to meet the requirements of valve opening. Keep the relative position of the valve plate to the valve body. The valve shaft shall bear the force of the medium and the transmission of the drive device to the butterfly plate, so as to ensure the valve's adjustment control or truncation function. To change the structure of the key to compensate for insufficient disc seal, you must first determine the compensation position (compensation width) required for the key.

        上一度:CSD941W水冷式超热竞技竞猜客户端使用说明 其次一个:先后29届中国国际测量控制与仪器仪表展览会Miconex2018邀请函
        回去列表
      1. 试点导航
      2. 资料下载
      3. 血站地图
      4. 自主经营权所有:热竞技竞猜客户端,热竞技竞猜APP生产企业-热竞技竞猜APP自控设备有限公司欢迎您!  营业产品:热竞技竞猜客户端|热竞技竞猜APP|高频蝶阀|   京ICP备05016881号

        艺术支持:蓝杉互动
      5. 在线咨询
      6. 010-60254227
      7. sale@adqvalve.com
      8. 法定微信